Sorry, nothing was found. Please change your selection and try again.
Showing 241 - 280 of 706 results
Filters
Sort by:
Best Match
Best Match
Price: Low to high
Price: High to low
Gedore ring spanner UD profile 34 mm
Optimal fit thanks to precisely crafted jaw and UD profileAngled at 15° for easier handlingUD profile for optimal power transmission and protection of screw heads
Gedore Pipe Wrench, Swedish Model, 2'' 175 2 L/W/H: 580x95x30 6437500
Square tube wrench made of chrome-vanadium special steelHead angled at 85°DIN 5234, Form ASwedish modelNon-loosable adjusting nutEspecially robust designFor pipes with 2-inch diameterLength: 580 mm
Gedore Socket Ring for Freewheel Ratchet UD Profile 46 mm 31 R 46 L/B/H: 70x70x32 6248450
Insert ring made of vanadium steel 31CrV3Manganese-phosphated surfaceNet weight: 0.422 kgSuitable for wrench size 46 mmMaterial: chrome-vanadium steel 31CrV3Diameter: 70.0 mm
Gedore Single Open-End Wrench 80 mm 894 80 L/B/H: 645x160x23 6577860
Open-end wrench according to DIN 894 ISO 3318Manganese-phosphated up to 38 mm Wrench Size, steel gray from 41 mm Wrench SizeSize 10 135 mm with hanging holePrecisely ground open end to exact nominal size for optimal contact surfacesOpen-end angle 15°Secure grip thanks to profile shaft, ergonomic and handyTechnical data: Wrench size 6 135 mm, length 73 1000 mm
Gedore Torque Wrench DREMOMETER EL A+S 1'' 750-2000 Nm 7569-01 L/B/H: 0x0x0 1547240
Torque wrench with locking mechanism and safety catch (A+S)Classified according to DIN EN ISO 6789-2:2017 Type II Class ACalibrated to +/3% deviation for precise useHigh operational safety thanks to drive square and pivot point aligned on the same axisApplication range from 6 3000 Nm in industrial manufacturing environmentsAutomatic short-range release with signalGedore 7569-01 Torque wrench 1" (25 mm) 750 2000 Nm
source: Amazon
Gedore Socket Wrench 16 Z 8791-13/16AF L/B/H: 63x45x36 1211439
16-Tooth Socket Wrench, 13/16"Made of Chrome Vanadium SteelForged and Matte ChromedEasily ReplaceableWith Pin LockIdeal for Solving Difficult Assembly Problems
£42.56
Gedore Replacement Pull Hook Set 150 mm 1.92/70 L/W/H: 160x115x35 1583344
Puller hook set with a length of 150 mmNo need to drill out the bearing cagePrevents chips in other componentsHook head secured against slippingComplete set enables removal of over 40 bearingsMaterial: Steel
Gedore hydraulic nut splitter 1.26/1 HYD L/W/H: 180x165x35 8009450
Hydraulic nut splitterSuitable for nuts up to strength class 10Chisel in the cutting area induction hardenedNo chipping of the cutting edgeBevel on the chisel edge improves the splitting effectSmooth chisel functionChannel walls knurled for mirror-smooth and wear-resistant use
Gedore Puller Set 1.07/K-2 L/W/H: 475x382x143 1676008
Puller set with 9 hooksMax. pulling force 5.0 tPlastic case with 2 spindlesOne 2-arm and one 3-arm crossbar each3 slim pulling hooks in 3 lengthsSecond spindle in case 1.07/K saves working time1.07/K-2 double-sided with nubby insert
Gedore Spindle SW 22, M20x2.5, 235 mm 129,506 L/W/H: 0x0x0 1084771
Pressed pressure piece (ball)Hardened spindle surface, wear-resistantStandard thread for rapid force build-upAlloy steel according to EN 10083Note: The spindle thread must be lubricatedMetric ISO thread
Gedore oil filter wrench
Oil filter claw with 12.5 mm (1/2") drive or 24 mm external hexSuitable for loosening seized oil filters and granulate cartridges on compressed air dryers with right-hand threadWith 3/8" internal square drive and 1/2" to 17 mm adapterClamping range from 60 mm to 120 mmNet weight: 0.65 kg
Gedore VDE socket wrench insert 1/2'' 6-point 32 mm VDE 19 32 L/B/H: 62x51x51 6123830
Hexagonal, manually operatedInternal square drive according to DIN 3120 C 12.5GEDORE Vanadium steel 31CrV3Protectively insulated up to 1000 V according to EN 60900/IEC 60900Double check-tool insulationInsulation overhang of 16-18 mmNon-standard diameter d1 for sizes 27, 30, and 32
Gedore torque screwdriver bit 1'' 6-point 22 mm K 21 22 L/B/H: 55x54x54 6183060
Design according to DIN 3129 ISO 2725-2Machine-operatedCompatible with all common pneumatic and electric screwdriversInternal square drive according to DIN 3121 H 25 ISO 1174GEDORE special steel, blackenedFrom SW 75 mm use No. KB 3770 and No. KB 3775, * not standardizedMaterial: special steel
Gedore Socket Ring Spanner 22 Z 8796-36 L/B/H: 108x54x39 7708410
Box-end wrench with 36 mm width across flatsMade of chrome-vanadium steel, forged and matte chrome-platedEasily replaceable with pin lockingOverall width of 54 mmWeight of 0.39 kg
Gedore Glue Grip Pliers, 220 mm, Clamping Range 30-60 mm 137 T L/W/H: 230x65x19 6403600
Grip clamp with a length of 220 mmFor clamping or securing longitudinal and corner jointsRelease lever blue dip-insulated, nickel-platedSuitable for various applications such as baseboards, trims, handrails, countertopsOperation: join workpieces, mark drill points, drill holes, apply glue, join, insert clamp, align, close clamping leverGlue grip clamp with a length of 9 inches (approx. 22.9 cm)Material: metal
GEDORE impact wrench SW70mm DIN133 GEDORE
Box Wrench No. 133Made of Chrome-Vanadium Steel 31CrV3SW 27 to SW 110Material C35 from SW 115DIN 133Suitable for heavy continuous use
Gedore 3/4" UD Profile Socket Insert 1 (D 32 1.13/16AF)
Socket wrench insert for professional use in industry and craftsInternal square drive according to DIN 3120-D 20 ISO 1174 with pin lockTextured knurling for easy handlingMade of GEDORE Vanadium steel 31CrV3, chrome-platedWrench size from 7/8 to 2 inchesDrive receptacle square 3/4 inchDimensions: length 51.5 to 68.5 mm, diameter 1 33.6 to 69.2 mm, diameter 2 36.0 to 48.0 mm, head depth 19.0 to 34.5 mm
Gedore Single Open-End Wrench 90 mm 894 90 L/B/H: 690x170x24 6578080
Key length is 690 mmSurface in steel grayWith hanging hole for easy storageJaw angle of 15° according to DIN 894 / ISO 3318Made from CV steelPrecisely ground jaw for optimal contact surfaces
Gedore Insert Open-End Wrench SE 9x12, 9 mm 7112-09 L/B/H: 40x26x15 7679050
Box-end wrench made of forged chrome-vanadium steelEasily replaceable thanks to pin lockingWrench size from 7 to 19 mmDrive socket rectangular 9 x 12 mmHead height from 5.5 to 7.5 mmHead width from 20.0 to 41.0 mmPitch of 17.5 / 20.0 mm
Gedore flat pliers 8305-9 L/B/H: 152x56x19 6726370
Straight shape without strikeESD = electrostatic dischargeGedore 6726370 flat pliersLength: 135mm
Gedore Quick-Release Puller 3-Arm 1.07/1A-E L/W/H: 180x165x35 1225901
Industrial quality with optimal load distribution systemRobust, ergonomically shaped crossbarHooks forged red-hot in the dieNitrocarburized spindle surface for wear and corrosion resistanceSmooth, clean spindle operation without grease or oilCompatible with other spindle and hook designs from the GEDORE puller modular system
Gedore Combination Wrench UD Profile 1 5/16'' 1 B 1 5/16AF L/B/H: 415x68x40 6006950
Ring wrench with high precision fitOffset ring angled at 10° for full torqueOpen-end thickness: 11.8 mm, ring thickness: 20.5 mm, overall length: 412 mmSuitable for recessed or countersunk nuts and bolts
Gedore Hook Wrench, DIN 1810 Form B, 135-145 mm (40 Z 135-145)
Hook wrench for cross-hole nutsWrench size from 135 to 145 mmPin diameter of 8 mmLength: 385 mm, Weight: 829 g
Gedore torque screwdriver bit 1'' hex 27 mm K 21 27 L/B/H: 55x54x54 6183220
Impact screwdriver bit with 1-inch internal square driveSuitable for all common pneumatic and electric screwdriversManufactured according to DIN 3129, ISO 2725-2Made from GEDORE special steel, blackenedNot standardized from SW 75 mm onwardsDimensions: SW 27 mm, length 59 mmFits SW 75 mm No. KB 3770 and No. KB 3775
Gedore screwdriver bit 1'' internal hex 24 mm IN 21 24 L/B/H: 92x49x49 6181440
Version according to DIN 7422 and internal square drive according to DIN 3120 D 25, ISO 1174With pin locking and grippy cross knurlingChrome-plated and made of GEDORE vanadium special steel, manganese phosphatedHand-operated
Gedore Pliers for External Retaining Rings, Angled 8000 A 41 EL L/B/H: xx 2011786
Assembly tool for circlip pliersSuitable for external rings from 85-140mm90° angled tips, zinc-platedLocking lever handle end dip-insulatedReinforced safety armsPrecisely machined, oil-hardened and temperedMaterial: chrome-vanadium steelOverall length: 580 mm
Gedore Single Open-End Wrench 95 mm 894 95 L/B/H: 830x190x28 6578160
Open-end wrench with a jaw width of 95 mmSteel gray finish with hanging holeJaw angle of 15° according to DIN 894 / ISO 3318Wrench length is 847 mmMade of CV steelRatchet function includedTotal weight of 6.335 kg
Gedore Internal Puller 46 - 56 mm 1.30/7 L/W/H: 165x45x45 8013800
Internal puller for ball bearings, rings, bushings, and oil sealsExpansion range from 45-55 mmSpindle nitrided for wear protectionOver 17,000 tools in the range
Gedore Dremometer D 8568-10 L/B/H: 830x110x65 7691850
Torque wrench with 3/4" square driveOperating range from 155 760 NmClassified according to DIN EN ISO 6789-2:2017 Type II Class AAutomatic short-release with signalNo value shifts due to two-handed operation
Gedore Thread Adapter Set with Slide Hammer 200 g, 7 t (1.81/K-1)
Thread adapter for removing threaded caps with a threaded holeSet includes a slide hammer with a 200 g impact weight and 6 thread adaptersWeight: 1000 g
Gedore Wire Stripping Side Cutter 8315-160 JC L/B/H: 173x66x34 1396722
Electrician's side cutter with dual function: cutting and strippingStripping holes for single and multi-stranded conductors with 1.5 mm² and 2.5 mm² conductor cross-sectionInduction-hardened precision cutting edges, cutting hardness 61 63 HRCGEDORE special tempered steel, drop-forged, oil-hardened and temperedVersion JC = chrome-plated, with 2-component handle grips
Gedore universal puller 3-arm with hook brake 1,07/11-B L/B/H: 0x0x0 1957945
Secure and concentric pulling through even load distribution on 3 pull hooksPull hooks forged from a single pieceEquipped with hook brake to prevent unintended slipping of the hooksHooks on the crossbar adjustable by pressing a buttonUsable as external and internal puller by repositioning the hooksInterchangeable hooks available for different clamping depthsUpgradeable with hydraulic spindle (see table)
Gedore Hex Key Attachment Inbus 16 Z 8756-05 L/B/H: 55x36x55 7773900
Accessories for torque wrenches with 16 mm square driveEasily replaceableForged from chrome-vanadium steelMatt chrome-platedWith pin lockingFor solving difficult assembly problems
Gedore torque wrench DREMOMETER C A+S 1/2" 50-3 (7562-10)
Series: Blue, Weight: 2 kgVersion: A+S fuse, aluminum alloyDimensions: L605 x W35 x H30 mmDrive: Solid square drive, 12.5 mmTorque range: 60 300 NmDIN EN ISO 6789-2:2017 Type II Class AAutomatic short-path release, tactile and audible signal
Gedore Insert Open-End Wrench SE 9x12, 14 mm 7112-14 L/B/H: 41x34x15 7689360
Insert wrench made of forged CV steelMatte chrome-plated surfaceSuitable for torque wrenchesWrench size: 14 mmOverall length: 42 mmWith pin lockEasily replaceable
Gedore Universal Puller HIGH POWER with Hook Brake 1,04/HP1A-B L/B/H: 0x0x0 1981145
Universal Puller HIGH POWER for powerful removal of ball bearings, wheels, discs, etc.Usable as both internal and external puller by repositioning the hooks2 arms, available in 3 versionsReinforced crossbar allows double pulling forceHooks forged from a single piece, with hook brake to prevent slippingAdjustment scale on crossbar for even hook positioningReplaceable spindle tip, spindle thermochemically hardenedDimensions: external span 130-350 mm, clamping depth 100-200 mm, weight 1.2-7.7 kg
Gedore Flaring Tool boerdex 233001 L/B/H: 215x130x40 4537300
Flanging tool for copper and light metal pipesSuitable for refrigeration systems and cooling technologyBody made of zinc die-cast, blue paintedFlanging cone with 90° hardness for 45° bendingWith pressure piece for 180° bendingClamping jaws made of steel, smooth and phosphated inside
Gedore 3/4'' UD Profile Socket Insert 55 mm D 32 55 L/B/H: 75x75x70 6273480
Socket with 3/4 inch drive12-point designWrench size 55 mmLength 68.5 mmMade of vanadium steel 31CrV3Matte chrome-plated finishNon-standard
Gedore 8316-200 JC Power Diagonal Cutter 200 mm, 2-Component Handle
According to DIN ISO 5749Large leverage for easy cuttingInductively hardened precision blades, cutting hardness 63-65 HRCMax. cutting capacity Ø 1.4–2.0 mmGEDORE special alloy steel, drop-forged, oil-hardened and temperedJC = chrome-plated, with 2-component handle protective coversLength: 200 mm, Weight: 340 g
Gedore torque screwdriver bit 1'' long hex 27 mm K 21 L 27 L/B/H: 100x54x54 6185510
Power screwdriver bit K 21 L 1" with internal square drive according to DIN 3121 H 25 ISO 1174Suitable for electric and pneumatic impact wrenchesLong version with pinhole and ring grooveMaterial: special steel, bluedWrench size: 27 mmLength: 100 mmCompatible with standard pneumatic and electric screwdrivers
Refine Search
Filters
Clear All
Category
✓Price
✓Brand
1Seller
0
